Silentknight 5808 User Manual Page 68
- Page / 180
- Table of contents
- TROUBLESHOOTING
- BOOKMARKS
Rated. / 5. Based on customer reviews
IntelliKnight 5808 Installation Manual 151274-L8
5-7
5.8 Addressing SD Devices
This section tells how to address detectors and modules.
5.8.1 SD505-APS, SD505-AHS, & SD505-AIS
The SD505-APS photoelectric smoke detector, SD505-AHS heat detector, and SD505-AIS ionization smoke
detector are easily addressed at the FACP. The Installer Code is required to perform this task.
To address a SD505-APS, SD505-AHS, or SD505-AIS:
1. Connect a detector base temporarily to the programming terminals as shown in
Figure 5-7. (You can use the same base for each detector).
Figure 5-7 Temporary Connection of Detector Base to Panel for Addressing
2. Enter the Installer code, then press
ENTER.
3. Select 2 for Point Functions.
4. Select 3 for Set SLC Dev Addr.
5. Select “Yes” by pressing the up arrow, then press
ENTER. (The panel will go into trouble at this point. You
can use the SILENCE key to stop the PZT. The trouble will clear automatically when the panel reinitializes
when you finish programming.)
6. When the wait message clears, the following options display:
1- for Read Address. Use to read (or check) a single detector’s address.
2 - for Write Address. Use to program a single detector’s address.
3 - for Seq. Programming. Use to program more than one detector in sequential order.
7. If you are changing addresses, write the programmed address on the back of the device.
8. To exit press left arrow until fully exited.
- INTELLIKNIGHT 1
- MODEL 5808 1
- Installation Procedure 2
- Contents 3
- Section 5 4
- Section 6 5
- Section 7 5
- Section 1 9
- Introduction 9
- 1.2 About this Manual 10
- 1.3 Compatible Products 11
- Manufacturer Model 12
- Section 2 15
- Systems 17
- Section 3 18
- Before You Begin Installing 18
- 3.3 Electrical Specifications 19
- 3.4 Wiring Specifications 20
- 3.5 Board Assembly Diagram 21
- Warning! 27
- Section 4 30
- Control Panel Installation 30
- 4.2 AC Connection 31
- 4.3 Battery Connection 31
- 4.3.1 RBB Accessory Cabinet 32
- 4.4 SBUS Wiring 34
- 4.4.2 Wiring Configurations 36
- 4.5.1 Mounting the 5860 38
- 4.5.1.1 Flush Mounting 39
- (outline) 40
- Installation 41
- 4.6.1 Selecting 5824 Options 42
- 4.7 5880 LED I/O Module 43
- 4.7.2 FACP Connection 44
- 4.7.3 LED Wiring 45
- 4.7.4 Dry Contact Wiring 46
- 4.8.1 FACP Connection 47
- 4.8.2 5865 Mounting 48
- 4.9 Configuring Modules 49
- 4.10 Telephone Connection 50
- 4.11.2.1 Door Holder Power 52
- 4.11.2.2 Constant Power 53
- 4.11.2.3 Resettable Power 53
- 4.11.2.4 Sounder Sync Power 53
- 4.12.1 Trouble Relay 54
- 4.12.2 Programmable Relays 54
- 5.2 List of SD SLC Devices 63
- 5.3 Maximum Number of Devices 63
- 5.5 SK Detector Installation 66
- 5.6 Addressing SK SLC Devices 67
- 5.7 SD Detector Installation 67
- 5.8 Addressing SD Devices 68
- Programming Overview 70
- ENTER to view the Main Menu 71
- ENTER to accept 71
- 6.2 Mapping Overview 73
- 6.2.1 Input Point Mapping 74
- 6.2.2 Output Circuit Mapping 75
- 6.2.3 Zone Event Mapping 76
- 6.2.4 Mapping LED Points 78
- To exit the programming menu: 79
- 6.4.4 Editing Keys 80
- Programming 93
- 7.2.1.1 Naming Modules 94
- 7.2.1.2 Module, Wiring Class 94
- 7.3 Zone 95
- 7.3.1.1 Edit Zone Name 96
- 7.3.1.2 Edit Zone Properties 96
- 7.3.1.3 Zone Outputs 98
- 7.3.1.4 Cadence Patterns 100
- 7.3.2 Add Zone 101
- 7.3.3 Delete Zone 101
- 7.3.4 View Zone Points 101
- 7.4.1.1 Edit Group Name 102
- 7.4.1.2 Edit Group Properties 102
- Option Description 103
- SILENCE key will be ignored 103
- 7.4.2 Add Group 104
- 7.4.3 Delete Group 104
- 7.4.4 View Group Points 105
- 7.5 Point 106
- Table 7-5 Point Programming 107
- Programming 151274-L8 108
- Choices Type Selections 111
- Function 111
- Selections for 111
- Comments 111
- 7.6.1.1 Edit Accounts 113
- 7.6.1.2 Auto Test Time 115
- 7.6.2.1 Dialing Prefix 116
- 7.6.2.4 Rotary Format 117
- 7.6.2.5 Line Monitor 117
- 7.6.3.1 Trouble Events 117
- 7.6.3.2 System Alarm Cadence 118
- 7.6.4.1 Water Flow Delay 119
- 7.6.4.3 Low AC Report Delay 120
- 7.6.5.4 Plex Door Option 121
- 7.6.7 Edit Banner Message 122
- 7.6.8 SLC Family 123
- 7.7 JumpStart Autoprogramming 124
- 7.8 Computer Account 124
- 7.9 Access Codes 124
- 7.9.1 Profile Edit Menu 125
- 7.9.1.1 Edit Name 126
- 7.9.1.2 Edit Access Code 126
- 7.9.1.3 Panel Functions 126
- Section 8 127
- System Operation 127
- 8.3 Key Operation 128
- 8.4 Menu System 129
- 8.5 Basic Operation 130
- 8.5.6 View Event History 131
- 8.5.7 Clear Event History 131
- 8.5.8 Conduct a Fire Drill 131
- 8.5.10 Conduct a Walk Test 132
- 8.5.11 Conduct a Dialer Test 132
- 8.5.13 Reset Alarms 132
- 8.5.20 Working with a Printer 135
- 8.6 Operation Mode Behavior 136
- System Operation 151274-L8 138
- Operation 139
- 8.7 Releasing Operations 141
- 8.8 Smoke Alarm Verification 144
- Section 9 145
- Reporting 145
- Reporting 151274-L8 146
- Section 10 154
- Testing and Troubleshooting 154
- 10.2.2 Event History 156
- 10.3.1 SLC Device Locator 156
- 10.3.2 SLC Multi Locator 156
- 10.3.3 I/O Point Control 157
- Section 11 159
- Installation Records 159
- Appendix A 161
- Compatible Devices 161
- Compatible Devices 151274-L8 162
- A.2 Two-Wire Smoke Detectors 171
- Table A-3 Low Frequency Bases 173
- Appendix B 174
- Special Characters Lists 174
- General Terms and Conditions 175
- Repair and RMA Procedure 175
- Advanced Replacement Policy 175
- 177
- Cut Along the Dotted Line 178
Related products and manuals for Safety Silentknight 5808
Safety Silentknight 5820XL User Manual
(236 pages)
(236 pages)
Safety Silentknight EVS User Manual
(74 pages)
(74 pages)
© 2020, manymanuals.com. All rights reserved. | 1.113 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals